Multiway Straps Explained: How to Wear Curvy Kate Clear Multiway Strapping

Quick answer

Attach the clear straps to your bra's loops, adjust the sliders while the bra is on, and choose the configuration that matches your neckline: standard, crossed, halter, or one-shoulder. For backless or low-back tops, use the included low back adjuster to drop the strap line below your shoulder blades. Always test the fit for five minutes before you leave — clear straps stretch slightly with body heat.

Clear multiway straps solve a specific problem: you want the support of a bra without visible straps ruining a strapless, backless, or asymmetric neckline. Curvy Kate Accessories Clear Multiway Strapping is a practical kit that gives you several wearing options from one set of straps.

This guide walks through the exact steps to attach, adjust, and wear them — including the low back adjuster that most people miss. It also covers the mistakes that cause slipping, digging, or visible plastic shine, so you can get a secure fit the first time.

What comes in the Curvy Kate Clear Multiway Strapping kit

The kit includes two fully adjustable shoulder straps, one fully adjustable back strap, and one low back adjuster. The material is 100% thermoplastic polyurethane, which is what gives the straps their stretch and transparency. Because they are clear, they work with any bra colour underneath — but they are not invisible under tight, shiny, or heavily textured fabrics.

The multiway options mean you can wear the straps in a standard over-the-shoulder position, crossed at the back, halter-style around the neck, or as a single strap for one-shoulder tops. The back strap and low back adjuster are separate pieces, so you can convert a regular bra into a low-back bra without buying a new one.

• Two shoulder straps, one back strap, one low back adjuster — check all four pieces before you start.
• The straps are adjustable, but the plastic sliders can loosen over time; re-check them before each wear.

Step-by-step: how to attach and wear clear multiway straps

Start with your bra off. Locate the small fabric loops or hooks at the top of your bra cups — these are where the straps attach. If your bra has detachable straps, remove them first. Open the clear strap's hook and slide it through the bra loop, then close the hook. Repeat on the other side. If you are using the low back adjuster, attach it to the back of the bra band before putting the bra on.

Once the straps are attached, put the bra on and adjust the sliders. Tighten until the bra band sits snugly against your ribcage and the cups lie flat — not digging, not gaping. For a crossed-back configuration, clip the straps to the opposite side loops. For a halter, bring both straps around your neck and connect them at the back of your neck. For a one-shoulder look, use only one strap and tuck the other side's loop flat against the cup.

• Common mistake: attaching the strap hook the wrong way, so the slider faces your skin. The slider should face outward for easy adjustment.
• Checkpoint: after adjusting, raise your arms overhead and roll your shoulders. If the band lifts or the straps dig, loosen the sliders slightly.

How to wear clear straps with strapless and backless tops

For a strapless top, you can wear the bra without any shoulder straps — but clear straps add security if you are moving around a lot. Attach only the shoulder straps and leave the back strap off. For a backless top, use the low back adjuster: it connects the two back straps and pulls the strap line down below your shoulder blades, so the back of your bra stays hidden under a low-cut back.

If your top has a very low or scooped back, the low back adjuster may still show. In that case, choose a bra with a matching band colour or use the clear straps in a crossed-back position to keep the lines higher. Clear straps are less visible than fabric straps, but they can catch the light — matte fabrics hide them best.

• For backless tops, always attach the low back adjuster before putting the bra on; it is much harder to attach once the bra is on.
• If the clear straps shine under flash photography, switch to a nude fabric strap or go strapless.

Making clear straps comfortable for all-day wear

Clear plastic straps do not breathe like fabric, so they can feel sticky or sweaty after a few hours. Keep the adjustment slightly looser than you would with fabric straps — the bra band should do most of the support work. If the band is too loose, the straps will dig into your shoulders, which is the most common cause of discomfort.

You can also alternate configurations during the day: start with standard straps for support, then switch to crossed or halter if you change outfits. The straps are fully adjustable, so you can fine-tune the length without removing the bra. If you feel redness or deep indentations, the straps are too tight — loosen them and tighten the band instead.

• Wash the clear straps by hand with mild soap and lukewarm water; harsh detergents can cloud the plastic.
• Store them flat or loosely coiled — sharp folds can create permanent creases that may crack over time.

Your step-by-step clear strap routine

1. Check your bra has detachable strap loops: Look for small fabric loops or plastic hooks at the top of the cups. If your bra has permanently sewn straps, clear multiway straps will not attach without modification. No loops? Use a strapless bra instead.
2. Attach the clear straps before putting the bra on: Open each strap hook, thread it through the bra loop, and close it. Make sure the adjustable slider faces outward, away from your skin. Attaching straps while wearing the bra is fiddly and often leads to twisted straps.
3. Add the low back adjuster for backless tops: Clip the low back adjuster to the back of the bra band before wearing. It pulls the strap line down below your shoulder blades. Skip this step only if your top fully covers your bra band.
4. Put the bra on and adjust the sliders: Tighten the shoulder straps until the cups lie flat and the band stays snug. Then loosen slightly if you feel pressure on your shoulders. The band should carry most of the support — not the straps.
5. Test the configuration with movement: Raise your arms, roll your shoulders, and bend forward. If the band lifts or the straps slip, re-adjust the sliders or switch to a crossed-back configuration. Five minutes of testing prevents a day of readjusting.

Product facts that matter for fit

• Curvy Kate Accessories Clear Multiway Strapping Clear: Includes two fully adjustable shoulder straps, one fully adjustable back strap, and one low back adjuster, made from 100% thermoplastic polyurethane. The separate back strap and low back adjuster let you convert a regular bra for low-back tops without buying a new bra; the adjustable sliders mean you can fine-tune length for different necklines.
• Curvy Kate Wild Horizon Non-Wired Multiway Tankini Top Black Print: Designed with adjustable straps and a multiway fit, non-wired and non-padded cups, and adjustable drawstring sides to control body length. If you already wear multiway swimwear, the same clear straps can work with tankini tops that have detachable straps — just check the loop width matches.

Clear multiway straps are a small accessory that makes a big difference for strapless, backless, and asymmetric outfits. Attach them before you dress, use the low back adjuster when your top dips low, and keep the band snug so the straps only guide — not carry — the support. With the right configuration, you get a secure fit without visible straps.